|
Upgrade ArcaOS to NeoWPS level
- Install original PNG icons drawed by designer, specialized at OS/2 adornation.
- Install eSchemes 2018 to change colors and buttons on desktop.
|
TITLE: TCP/IP tuner
DATE: 2004-02-28 23:18:27
AUTHOR: Roderick Klein
Please use online translator
go to http://translate.google.com
and request the translation of http://en.ecomstation./showarticle.php?id=101
to your language |
If you are using eComstation 1.1 and you are experiencing frequent traps
(kernel dumps) then please read the following! People who use OS/2 (MCP
4.51 or MCP2 4.52) or WSeB or eComStation 1.0 this information might also
be usefull for!
eComStation 1.1 CD #2 contains the "TCP/IP tuner" (In both the German and
English version). People who used this tool, please pay attention.
Q. First of all: how can I tell if I have installed this TCP/IP tuner?
A. Look in the directory \mtpn\etc\ for the file inetcfg.ini. If you do
not know much about TCP/IP and the file is present, you most likely
installed the TCP/IP tuner from CD #2. If the inetcfg.ini file is found,
open it in an editor and look for the line with the term SACK, with a
number 1 behind it.
What to do:
If that option is set to 1, remove the line from the file and save the
file, to make certain the new settings are activated you should reboot
your system!
Background information:
Q: Why was the TCP/IP tuner introduced ?
A: People using Netscape 4.61 sometimes experience "broken pipe" messages
on OS/2. Also the commandline tool nslookup.exe (to look up the IP adres
that belongs to a domainname) sometimes is *very slow* or times out.
If this is the case you will likely experience timeouts with other
applications as well, because your system cannot properly connect to
other systems on the internet. Overall TCP/IP performance can be bad
(especially on dialup connections)
To overcome these issues, the TCP/IP tuner was introduced. It will change
a couple of the default TCP/IP settings to increase performance and
reliability.
Q: What is the problem with the SACK setting ?
A: SACK means Selective Acknowlegdement. It is used between computers
communicating over the internet or a LAN with the TCP/IP protocol. *Early*
research seems to indicate that TCP/IP stack contains a bug. There are so
called RFC's documents that describe how network protocols and its
features should work. When connections are made to a computer connected to
a network, the computer will allocate memory buffers etc. As connections
are closed or timeout this allocated memory is released.
When an OS/2 or eComStation system has the SACK option set to 1 somehow
these buffers do not seem to be released. The result is that more and more
of your systems RAM gets allocated (so called MBUFS).
You can verify this by using the following command from the commandline:
netstat -m:
Two lines are important:
mbufs obtained from page pool=
protocol control block mbufs=
If there are for example more then 5000 to 6000 buffers allocated then
you could be affected by the SACK setting. It is no problem if there is a
*peak* in the allocation of these buffers. The amount of buffers
allocated by the TCP/IP stack should be dynamic. If the buffers are not
released, the system will run out of memory (resources) and just lockup
or trap.
According to the RFC, SACK should only be used when another connecting
party also has SACK enabled.
This problem has also been reproduced on MCP 2 from IBM and an older
TCP/IP stack from 2001.
Who could be potentialy be affected by this:
- People who have a lot of web traffic because of surfing the internet
(people who have an ADSL or Cable internet connection).
- Especially people who run a webserver.
- People who use NetBIOS over TCP/IP
Closing note:
Everyone should apply the TCP/IP tuner to boost performance of the TCP/IP
stack in eComStation. However, make sure the SACK line is absent (or the
value set to 0) in the \MPTN\ETC\INETCFG.INI file.
Komentarze: Kirov Igor 
2004-02-29 23:37:11 | eComStation 1.1 CD #2 contains the "TCP/IP tuner" - ..... .... "....." .. ......... INETCFG.EXE ? | Pavel Shtemenko
2004-03-01 09:32:03 | ...... MBUF .. .. ...... inetcfg ....... ......... ;-) | Kirov Igor
2004-03-01 21:41:19 | . ..... INETCFG.INI ..... ...... .........? | Vincent Gfeller 
2006-07-03 13:29:22 | Is it normal that I doesn't have any INETCFG.INI on my wholw hard drive?
| hcilmoue
2010-07-19 04:58:06 | [URL=http://opsishyj.com]unedvuzl[/URL] <a href="http://iwczrkok.com">bjwalptt</a> ipxwvmlb [url] xyhirpks xsedflog |
Komentarz artykuЁu.
|
eComStation 2.0 can (automatically) switch between WiFi and Ethernet without headache. eCS 2.0 what's new? |
|
|
